Industry & business calculator

Electric motor energy savings calculator: premium efficiency motors and VFDs

Compare an existing motor with an IE3, IE4 or IE5 replacement using IEC 60034-30-1 efficiency classes, add a variable-speed drive for fans and pumps (affinity laws), and see the kWh, money and CO₂ saved and the payback.

Editable share link Branded PDF report Free · no sign-up

Results

The upgrade cuts consumption from 182,566 to 85,454 kWh a year (53% less), saving about 14,567 € and 44.5 t CO₂ a year. It pays back in 0.7 years and saves about 209,001 € over a 15-year motor life.
Annual saving
€14,567
97,111 kWh per year
Simple payback
0.7years
Existing motor efficiency
91.2%
IE1 at 37 kW
New motor efficiency
95.2%
IE4 at 37 kW
Electrical input now
30.4kW
Electrical input after
14.2kW
Saving from the motor alone
€1,151
7,671 kWh
Saving from the drive
€13,416
89,441 kWh
CO₂ avoided per year
44.5t
Running cost now
€27,385
2.9× the upgrade cost every year
Annual electricity use (kWh)
Minimum efficiency by class (4-pole, 50 Hz)

Efficiency classes at 37 kW

ClassEfficiencyInput power (kW)kWh/yrCost (€/yr)
IE191.2%30.43182,56627,385
IE292.7%29.94179,61226,942
IE393.9%29.55177,31626,597
IE495.2%29.15174,89526,234
IE596.2%28.86173,14925,972
  • IE1–IE4 values: IEC 60034-30-1 limits for 4-pole 50 Hz motors (interpolated); IE5 assumed 20% lower losses than IE4. Real motors often beat the minimum; efficiency also varies with load below ~50%.
  • Drive savings assume the flow is now throttled by a valve or damper (shaft power ≈ 55% + 45% × flow) and follow the affinity laws with a 3% drive loss. Systems with high static head save less.

Why motors are the biggest efficiency lever in industry

Electric motors use roughly half of the world’s electricity, and about 70% of industrial electricity. The IEA’s motor systems work puts the share even higher in some sectors. A single motor running two shifts can use electricity worth three or four times its purchase price every year. So a few points of efficiency, or a smarter way of controlling flow, often pay back faster than almost any other industrial measure.

This calculator compares the motor you have with a better one, using the minimum efficiencies of the IEC 60034-30-1 classes. It can also add a variable-speed drive for fans and pumps whose flow is now throttled by a valve or damper. You get yearly kWh, cost and CO₂ for each step and the payback on the combined investment.

The formula

Shaft power P_shaft = rated kW × load Electrical input P_in = P_shaft ÷ η_motor

With a drive (fans, pumps): throttled shaft power ≈ P_design × (0.55 + 0.45 × Q) speed-controlled ≈ P_design × Q^n ÷ η_drive n = 2–3, η_drive = 0.97

Annual kWh = P_in × hours Saving = (kWh_old − kWh_new) × price Payback = installed cost ÷ annual saving

The efficiency for each class is interpolated from the IEC 60034-30-1 table for 4-pole, 50 Hz motors at the rated power you enter. IE5 is taken as 20% lower losses than IE4. The throttling curve is a simple approximation for valve or damper control; outlet dampers and bypass control behave somewhat differently.

Worked example

The defaults describe a 37 kW pump motor at 75% load running 6,000 hours a year, an old IE1 machine replaced by an IE4 motor with a drive. The pump’s average duty needs only 70% of design flow.

  • Existing: 27.75 kW shaft ÷ 0.912 = 30.4 kW input, 182,600 kWh a year, about 27,400 at 0.15/kWh.
  • New IE4 motor alone: 27.75 ÷ 0.952 = 29.1 kW, saving about 7,700 kWh (1,150) a year.
  • Adding the drive: the design-point shaft power is 27.75 ÷ 0.865 = 32.1 kW. At 70% flow with an exponent of 2.5 it needs 32.1 × 0.41 = 13.2 kW of shaft power, and 14.2 kW at the meter.
  • Total: 85,500 kWh a year, 53% less, saving about 14,600 a year and 44 t of CO₂ at the world average grid intensity. The 9,500 investment pays back in about 8 months.

The example shows a typical pattern: the motor upgrade saves a few percent, while matching speed to the actual duty saves tens of percent. Switch off the drive and compare the IE2 → IE3 preset on a conveyor running 4,000 hours, and the payback stretches past 12 years. For such a motor, upgrading at failure is the sensible strategy.

Minimum efficiency by class (4-pole, 50 Hz)

Rated power IE1 IE2 IE3 IE4
1.1 kW 75.0% 81.4% 84.1% 87.2%
4 kW 83.1% 86.6% 88.6% 91.1%
11 kW 87.6% 89.8% 91.4% 93.3%
37 kW 91.2% 92.7% 93.9% 95.2%
90 kW 93.0% 94.2% 95.2% 96.1%
200 kW and above 94.0% 95.1% 96.0% 96.7%

The 60 Hz values used in North America (NEMA Premium ≈ IE3) are slightly higher at the same power.

Tips for motor systems

  • Start with the duty, not the motor. Throttled pumps and fans, oversized motors running at 30–40% load and systems that run when nothing needs them waste far more than motor losses.
  • Replace instead of rewinding small and medium motors that run a lot: the price difference between a rewind and a new IE3/IE4 motor usually pays back quickly.
  • Check the power factor. Lightly loaded motors have poor power factor; see the power factor correction calculator.
  • Compressed air is often the most expensive utility driven by motors; quantify leaks with the compressed air leak calculator.

Limitations

Efficiencies are class minimums at full load; many real motors exceed them, and efficiency drops noticeably below about 50% load. A drive adds its own losses (2–4%) and harmonics, and it cannot save energy on constant-torque loads running at full speed. The throttling model is generic: get measured flow and pressure data for an accurate drive study. CO₂ uses the selected country’s average grid intensity.

Method & assumptions

Electrical input = shaft power ÷ motor efficiency, where shaft power = rated kW × load. Efficiency comes from the IEC 60034-30-1 class limits at the motor rating (log-interpolated). With a drive, the throttled operating point is replaced by a speed-controlled one: P ∝ Qn (affinity laws, n = 2–3), divided by drive efficiency 97%. Savings = ΔkWh × price; payback = installed cost ÷ annual saving; CO₂ uses the selected grid's average intensity.

Frequently asked questions

How much energy does an IE4 motor save compared with IE2?
Typically 2–4 percentage points of efficiency for motors between 1 and 100 kW, which is a 25–40% cut in motor losses. For a 37 kW motor at 75% load running 6,000 hours a year, going from IE2 (92.7%) to IE4 (95.2%) saves about 4,700 kWh a year.
What are the IE efficiency classes?
IEC 60034-30-1 defines IE1 (standard), IE2 (high), IE3 (premium) and IE4 (super premium) efficiency for line-operated motors; IEC TS 60034-30-2 adds IE5 (ultra premium), with about 20% lower losses than IE4. In the EU, most motors from 0.75 to 1,000 kW must meet IE3 since July 2021, and 75–200 kW motors IE4 since July 2023.
How much energy does a variable-speed drive save on a pump or fan?
Often 20–50%. Centrifugal pumps and fans follow the affinity laws: power falls roughly with the cube of speed, so running at 80% speed needs only about half the power. The saving is largest where flow is now reduced with valves or dampers and smallest where the system has a high static head.
Is it worth replacing a working motor with a more efficient one?
For motors running more than about 4,000 hours a year, replacing an IE1 or old rewound motor often pays back within 2–5 years. For low-hour motors it is usually better to wait until the motor fails and then buy IE3 or IE4 instead of rewinding.
Why is the electricity cost of a motor so high compared with its price?
A motor running most of the year uses electricity worth several times its purchase price every year. Over a typical 15–20 year life, energy accounts for well over 90% of total ownership cost, which is why efficiency matters far more than price.
Does rewinding a motor reduce its efficiency?
It can. Poor-quality rewinds that overheat the core can lose 1–2 points of efficiency. Good practice rewinds (following the EASA/AEMT guidelines) keep efficiency within about 0.5 points of the original.

Sources & references

  1. IEC 60034-30-1:2014 — Efficiency classes of line-operated AC motors (IE code)
  2. EU Commission Regulation 2019/1781 — Ecodesign requirements for electric motors and variable speed drives
  3. US DOE — Improving Motor and Drive System Performance: A Sourcebook for Industry
  4. IEA 4E Electric Motor Systems Platform (EMSA)

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.