Industry & business calculator

Data centre PUE calculator: facility energy, overhead cost and savings

Work out the power usage effectiveness (PUE) of a data centre from its IT load, cooling, UPS and other losses, or start from a known PUE, then see annual energy, cost, CO₂ and water, and what a lower PUE would save.

Editable share link Branded PDF report Free · no sign-up

Results

PUE is 1.48: for every kWh used by IT equipment, the facility draws 1.48 kWh in total. Annual consumption is 12,970 MWh, of which 4,210 MWh is overhead, costing 505,247 €. At a PUE of 1.3 the same IT load would save 189,887 € and 725 t CO₂ a year.
PUE
1.48
DCiE 67.5%
Facility power
1,481kW
Annual energy
12,970MWh
8,760 MWh for IT
Annual electricity cost
1.6million €
Cost of overhead
€505,247
cooling, power losses, building
Cost per kW of IT per year
€1,556
Saving at target PUE
€189,887
1,582 MWh per year
CO₂ per year
5,940t
Water per year
15,768m³
WUE 1.8 L/kWh
Where the power goes (kW)
Annual electricity cost vs PUE (€)

Energy balance

ComponentkWMWh/yrShare
IT equipment1,0008,76067.5%
Cooling375.53,29025.4%
UPS losses65.15704.4%
Transformers & PDUs201751.4%
Lighting & other201751.4%
  • PUE per ISO/IEC 30134-2 is measured over a full year at the facility meter; this tool uses average powers. With a known PUE the overhead split shown is illustrative (70% cooling).
  • Water use depends heavily on the cooling design and climate; enter your WUE (ISO/IEC 30134-9). CO₂ uses the selected country's average grid intensity.

What PUE measures

Every watt a server draws turns into heat that must be removed, and the electricity on its way to the server passes through transformers, UPS units and power distribution units that each lose a little. Power usage effectiveness (PUE) captures all of that overhead in one ratio: total facility energy divided by IT energy. It was introduced by The Green Grid in 2007 and is now standardised as ISO/IEC 30134-2.

Data centres are a fast-growing electricity load. The IEA estimates they used about 1.5% of global electricity in 2024 and expects that to roughly double by 2030, driven largely by AI. At that scale, every 0.1 of PUE is a lot of power.

This calculator works in two ways. You can build the PUE from components (cooling power per kW of IT, UPS efficiency, distribution losses and building loads), or enter a known PUE. It then gives annual energy, cost, CO₂ and water, and the savings from reaching a target PUE.

The formula

PUE = total facility energy ÷ IT energy DCiE = 1 ÷ PUE

From components (average kW): distribution losses = IT × loss % UPS losses = (IT + distribution) × (1 ÷ η_UPS − 1) cooling = IT × cooling ratio + 0.3 × (UPS + distribution losses) facility = IT + cooling + UPS + distribution + lighting & other

Annual MWh = facility kW × 8.76 Saving at target PUE = IT MWh × (PUE − PUE_target) × price

The extra cooling term reflects that UPS and transformer losses become heat inside the building and must also be removed. The 0.3 factor is a simple assumption equal to the default cooling ratio.

Worked example

The defaults describe a 1 MW IT load with cooling drawing 0.35 kW per kW of IT, a 94% efficient double-conversion UPS, 2% transformer and PDU losses and 2% for lighting and offices.

  • Distribution: 20 kW. UPS losses: 1,020 × (1/0.94 − 1) = 65 kW.
  • Cooling: 350 kW + 0.3 × 85 = 376 kW. Lighting and other: 20 kW.
  • Facility power: 1,481 kW, so PUE = 1.48 (DCiE 67.5%).
  • Annual energy: 12,970 MWh, of which 4,210 MWh is overhead. At 0.12/kWh the bill is about 1.56 million, and the overhead alone costs about 505,000.
  • Reaching PUE 1.3 with the same IT load would save about 1,580 MWh and 190,000 a year, plus about 725 t of CO₂ at the world average grid intensity.

The presets show the range: a legacy enterprise room lands around 1.74, while a hyperscale site with free cooling and eco-mode UPS reaches about 1.11.

Typical values

Facility Typical annual PUE
Small server room, comfort air conditioning 1.8–2.5
Older enterprise data centre 1.6–2.0
Industry average (Uptime Institute surveys) ≈ 1.55–1.6
Modern colocation facility 1.25–1.45
Hyperscale with free or liquid cooling 1.08–1.2

Climate matters: a site in the tropics needs mechanical cooling all year, while a Nordic site can use outside air most of the time.

How to improve PUE

  • Contain hot or cold aisles and seal gaps so cooling air goes through servers instead of around them.
  • Raise supply air temperature within the ASHRAE recommended range (18–27 °C); every degree lets chillers work more efficiently and extends free-cooling hours. Model chiller savings with the chiller energy cost calculator.
  • Use free cooling (air-side or water-side economisers) wherever the climate allows.
  • Choose efficient UPS modes and right-size modular UPS so modules run near their efficiency peak.
  • Consider liquid cooling for high-density AI racks, which removes heat with far less fan and chiller power.

Limitations

PUE says nothing about how efficiently the IT equipment itself uses power; consolidating idle servers often saves more energy than any facility upgrade. Average powers hide seasonal swings, so a real annual PUE needs metered data. The component split for a known PUE is illustrative. Grid CO₂ is the average for the selected country; for corporate reporting use the Scope 2 emissions calculator, which separates location- and market-based figures.

Method & assumptions

PUE = total facility energy ÷ IT equipment energy (ISO/IEC 30134-2). From components: UPS losses = (IT + distribution) × (1/ηUPS − 1); cooling = IT × cooling ratio + 30% of electrical losses (that heat must also be removed); total = IT + cooling + UPS + distribution + other. DCiE = 1 ÷ PUE. Annual MWh = kW × 8.76. Saving at target = IT MWh × (PUE − PUEtarget) × price.

Frequently asked questions

What is PUE in a data centre?
Power usage effectiveness is total facility energy divided by the energy used by IT equipment (servers, storage, network). A PUE of 1.5 means that for every kWh reaching the IT equipment, another 0.5 kWh goes to cooling, power conversion losses, lighting and other building loads. The ideal is 1.0.
What is a good PUE?
The industry average has been around 1.55–1.6 in Uptime Institute's annual surveys in recent years. New colocation facilities often target 1.2–1.4, and the most efficient hyperscale sites with free cooling report annual averages of about 1.1. Small server rooms with room air conditioners often run at 1.8–2.5.
How do I calculate PUE?
Measure total facility energy at the utility meter and IT energy at the UPS output or PDUs over the same period, ideally a full year, and divide. ISO/IEC 30134-2 defines the measurement categories. Spot readings in winter flatter the result, because cooling energy is lower.
What is DCiE?
Data centre infrastructure efficiency is the inverse of PUE, expressed as a percentage: DCiE = 1 ÷ PUE × 100. A PUE of 1.5 equals a DCiE of 67%, meaning two-thirds of the facility's energy reaches the IT equipment.
How much does it cost to run 1 kW of IT load for a year?
One kW running all year is 8,760 kWh at the IT equipment, multiplied by PUE at the meter. At PUE 1.5 and 0.12 per kWh that is about 1,580 a year, of which 525 is overhead.
What is WUE?
Water usage effectiveness (ISO/IEC 30134-9) is annual site water use in litres divided by IT energy in kWh. Sites with evaporative cooling towers often report 1–2 L/kWh; air-cooled sites with dry coolers can be close to zero. Lowering PUE with evaporative cooling can raise WUE, so the two must be weighed together.

Sources & references

  1. ISO/IEC 30134-2 — Data centres: Key performance indicators, Power usage effectiveness (PUE)
  2. Uptime Institute — Global Data Center Survey (annual)
  3. IEA — Energy and AI (2025): data centre electricity demand
  4. Lawrence Berkeley National Laboratory — United States Data Center Energy Usage Report

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.