Industry & business calculator

Demand charge calculator: peak kW billing, load factor and peak shaving

Split a commercial electricity bill into energy and demand charges, compute the load factor and the effective price per kWh, apply a ratchet clause, and see what shaving the peak (by load control or a battery) would save.

Editable share link Branded PDF report Free · no sign-up

Results

Load factor is 37%. Demand charges are 6,750 € (36% of the bill), and the effective price is 0.157 €/kWh instead of 0.1. Cutting the peak by 60 kW saves 900 € a month.
Effective price
0.157€/kWh
energy rate 0.1 €/kWh
Load factor
37%
average 164 kW vs peak 450 kW
Monthly bill
€18,850
Energy charges
€12,000
Demand charges
€6,750
450 kW billed
Demand share of bill
36%
Saving per month
€900
60 kW less peak
Saving per year
€10,800
Battery for this shaving
100kWh
60 kW for 1.5 h, 90% usable
Battery payback (demand only)
3.2years
battery about 35,000 €
Monthly bill before and after shaving (€)
Effective price vs load factor (€/kWh)

Peak shaving options

Peak reduction (kW)New peak (kW)Saving (€/month)Battery (kWh)Saving (€/year)
23428338384,050
45405675758,100
683831,01311312,150
903601,35015016,200
1353152,02522524,300
  • Load factor uses 730 hours per month. Tariffs differ: some bill the highest 15-minute peak, some 30- or 60-minute, some only in on-peak hours, and many have seasonal rates.
  • Battery sizing is a first estimate for a single daily peak; peaks on several days or longer than the duration entered need more energy. A battery may also earn energy arbitrage or grid-service income, not included here.

How demand charges work

A household pays for kWh. A factory, office or shop usually pays twice: once for the energy (kWh) and again for the highest power it drew during the month (kW, sometimes kVA). The utility’s meter averages power over 15- or 30-minute intervals and remembers the highest one. That single interval sets the demand charge for the whole month.

The reason is cost. Cables, transformers and generation must be sized for the peak, whether it lasts all day or ten minutes. For a site with a short, high peak, demand charges can be a third to two-thirds of the bill. This calculator splits the bill into energy, demand and fixed parts, computes the load factor and the effective price per kWh, and shows what a lower peak is worth, including the battery needed to achieve it.

The formula

Load factor LF = monthly kWh ÷ (peak kW × 730 h) Billed demand = max(actual peak, ratchet % × highest peak in last 12 months) Monthly bill = kWh × energy price + billed kW × demand charge + fixed charge Effective price = bill ÷ kWh = energy price + demand charge ÷ (LF × 730)

Peak-shaving saving = (billed kW before − billed kW after) × demand charge Battery energy ≈ kW reduction × peak duration ÷ 0.9 usable

Worked example

The defaults describe a factory using 120,000 kWh a month with a 450 kW peak, paying 0.10 per kWh, 15 per kW-month and a 100 fixed charge.

  • Load factor: 120,000 ÷ (450 × 730) = 37%. The average load is 164 kW, a little over a third of the peak.
  • Energy charges: 12,000. Demand charges: 450 × 15 = 6,750, which is 36% of the 18,850 bill.
  • Effective price: 18,850 ÷ 120,000 = 0.157 per kWh, 57% above the energy rate.
  • Shaving the peak by 60 kW saves 900 a month, 10,800 a year.
  • If the peak lasts about 1.5 hours, a battery needs about 100 kWh. At 350 per kWh it costs about 35,000 and pays back from demand savings alone in about 3.2 years.

The last preset shows the catch with ratchets. An EV depot with an 80% ratchet and a 750 kW peak from earlier in the year is billed for 600 kW anyway. Shaving this month’s peak from 600 to 450 kW saves nothing until the old peak rolls off.

Typical values

Site type Typical load factor Demand share of bill (at 10–20 per kW-month)
Cold store, data centre, 24/7 process 70–90% 15–25%
Three-shift factory 55–75% 20–30%
Single-shift factory 30–45% 30–45%
Office or school 25–40% 30–50%
EV fast-charging site 5–20% 50–80%

How to read the results

  • Effective price is what each kWh really costs once demand charges are spread over it. Use it, not the energy rate, to value efficiency or solar savings.
  • Load factor below about 40% means demand charges dominate and peak management is worth looking at.
  • The table of shaving options shows savings for 5–30% peak reductions. The first few percent are usually cheap, coming from load scheduling, while deeper cuts need storage.
  • Battery payback counts demand savings only. A battery that also stores solar or shifts energy to cheaper hours earns more; see the time-of-use savings calculator and the LCOS calculator.

Tips to cut the peak

  • Find the peak first. Interval data from the utility or a logger shows when it happens: often Monday morning start-up, a hot afternoon or a shift change.
  • Stagger start-ups of compressors, chillers, ovens and furnaces after a shutdown.
  • Shed non-critical loads automatically when demand nears a set limit.
  • Improve power factor if the tariff bills kVA demand. The power factor correction calculator shows the saving.
  • Charge EV fleets smartly so vehicles do not all start charging at once.

Limitations

Tariff structures vary widely: on-peak only demand, seasonal rates, coincident-peak charges, contracted capacity with penalties for exceeding it, or demand billed in kVA. Enter the numbers that match your bill and treat the result as an estimate. The battery sizing assumes one peak per day of the given duration and ignores degradation and round-trip losses beyond the usable-capacity factor.

Method & assumptions

Load factor = monthly kWh ÷ (peak kW × 730 h). Bill = kWh × energy price + billed kW × demand charge + fixed charge. Billed kW = max(actual peak, ratchet % × highest peak of the last 12 months). Effective price = bill ÷ kWh = energy price + demand charge ÷ (load factor × 730). Peak-shaving saving = reduction in billed kW × demand charge. Battery energy ≈ kW reduction × peak duration ÷ 0.9 usable.

Frequently asked questions

What is a demand charge on an electricity bill?
A demand charge bills the highest power you draw in the month, usually the highest 15- or 30-minute average in kW or kVA, at a price per kW. It pays for the network and generation capacity sized for your peak. Commercial and industrial tariffs almost always include one, and it can be 30–70% of the bill for sites with short, high peaks.
How is load factor calculated?
Load factor = energy used ÷ (peak demand × hours in the period). A site using 120,000 kWh in a month with a 450 kW peak has a load factor of 120,000 ÷ (450 × 730) = 37%. A high load factor means steady use and a low effective price per kWh.
How do I reduce demand charges?
Avoid starting large loads at the same time, stagger equipment start-ups after shutdowns, shift flexible loads such as pre-cooling, water heating or EV charging away from the peak, use load controllers that shed non-critical loads, and consider a battery for peak shaving. Improving power factor helps if demand is billed in kVA.
What is a demand ratchet?
A ratchet clause sets the billed demand to at least a percentage (often 50–90%) of the highest peak in the previous 11 or 12 months. A single high peak in summer can then raise your bills for a whole year, and peak-shaving savings only appear once that peak rolls out of the window.
Is a battery worth it for peak shaving?
It can be when demand charges are high (above roughly 10–15 per kW-month) and peaks are short. A battery that cuts 60 kW for 1.5 hours needs about 100 kWh; at 15 per kW-month it saves 10,800 a year, so payback is roughly 3–5 years depending on battery cost. Longer or more frequent peaks need a bigger battery.
Why is my effective price per kWh higher than the energy rate?
Because the demand charge is spread over your kWh. Effective price = energy rate + demand charge ÷ (load factor × 730). At a 37% load factor and 15 per kW-month, demand adds about 0.056 per kWh to a 0.10 energy rate.

Sources & references

  1. US DOE / NREL — Identifying potential markets for behind-the-meter battery storage: demand charges
  2. US EIA — Electricity explained: factors affecting electricity prices
  3. OpenEI — U.S. Utility Rate Database (demand charge structures)
  4. IEA — Demand response

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.