Industry & business calculator

Steam cost calculator: cost per tonne of steam, fuel use and CO₂

Cost of generating one tonne of steam from the boiler pressure, superheat, feedwater temperature, blowdown and boiler efficiency for gas, oil, coal, biomass or electric boilers, with hourly fuel use, annual cost, CO₂ and the value of condensate return.

Editable share link Branded PDF report Free · no sign-up

Results

Each tonne of steam at 10 bar(g) needs 672 kWh of heat, or 79.6 m³ of fuel at 88% boiler efficiency. Steam costs 49.23 € per tonne; at 10 t/h for 6,000 hours that is 2,954,099 € a year. Heating the feedwater by 10 °C more (for example with extra condensate return) would save about 51,581 € a year.
Cost per tonne of steam
49.23€/t
fuel 47.73 €/t
Heat per tonne
672kWh/t
2.42 GJ/t
Fuel per tonne of steam
79.6m³
Fuel per hour
796m³/h
Boiler heat output
6.72MW
Saturation temperature
184°C
steam enthalpy 2,781 kJ/kg
CO₂ per tonne of steam
154kg
Annual steam cost
3million €
60,000 t of steam per year
Annual CO₂
9,261t
Value of +1 point boiler efficiency
€32,181
per year
Value of +10 °C feedwater
€51,581
per year
Steam cost vs feedwater temperature (€/t)
Steam cost vs boiler efficiency (€/t)

Saturated steam properties

Pressure (bar g)Temperature (°C)h_f (kJ/kg)h_g (kJ/kg)Latent heat (kJ/kg)
099.94182,6752,257
2133.65622,7252,164
4151.96402,7482,108
6165.16972,7622,065
8175.27422,7732,030
101847812,7812,000
15201.28582,7921,934
20214.89202,7991,879
30235.61,0162,8031,787
40251.81,0942,8001,706
  • Steam properties are interpolated from IAPWS-IF97 saturated steam tables; superheat uses cp ≈ 2.1 kJ/kg·K and feedwater enthalpy 4.19 kJ/kg·K × temperature.
  • Efficiency and fuel energy must be on the same basis (NCV here). Distribution losses, condensate losses and steam trap failures add to the real cost of steam at the point of use.

What this calculator does

Steam carries heat to processes in food, chemicals, paper, textiles, refineries and hospitals. Its cost per tonne is the number energy managers use to price every steam user, judge improvements such as condensate return or economisers, and compare fuels or electrification. The calculation is a simple energy balance, but the details matter: pressure, superheat, feedwater temperature and blowdown all change the heat the boiler has to add.

Enter the steam conditions, the fuel and its price, and the boiler efficiency. The calculator returns the heat and fuel per tonne, the cost per tonne, hourly fuel use, annual cost and CO₂, and the value of one point of boiler efficiency and of 10 °C hotter feedwater.

The formula

Heat per tonne Q = (h_steam − h_fw) + blowdown × (h_f,sat − h_fw) (kJ/kg × 1,000)

h_steam = h_g(p) + 2.1 × superheat h_fw = 4.19 × T_feedwater

Fuel per tonne = Q ÷ boiler efficiency ÷ fuel energy content Cost per tonne = fuel × price + water & treatment + CO₂ × carbon price

Saturated steam enthalpies h_g and h_f come from the IAPWS-IF97 steam tables at the absolute boiler pressure (gauge + 1.013 bar). The table under the results lists them for common pressures.

Worked example

The defaults describe a 10 t/h gas-fired boiler making saturated steam at 10 bar(g) from 90 °C feedwater, with 4% blowdown, 88% efficiency and gas at 0.60 per m³ (9.6 kWh per m³ net).

  1. At 11 bar absolute, saturated steam has h_g ≈ 2,781 kJ/kg and the saturation temperature is 184 °C.
  2. Feedwater at 90 °C holds 377 kJ/kg, so the boiler adds 2,404 kJ per kg of steam. Blowdown adds 4% × (781 − 377) = 16 kJ/kg.
  3. Heat per tonne: 2.42 GJ = 672 kWh.
  4. Fuel: 672 ÷ 0.88 = 764 kWh, or 79.6 m³ of gas per tonne.
  5. Cost: 79.6 × 0.60 = 47.7 in fuel, plus 1.5 for water and treatment = 49.2 per tonne.
  6. At 10 t/h for 6,000 hours: 60,000 t of steam, about 2.95 million a year, and 9,300 t of CO₂.

One extra point of boiler efficiency is worth about 32,000 a year here, and 10 °C hotter feedwater about 52,000. That second number is why condensate return and economisers are usually the first projects in a steam audit.

Typical values

Item Typical range
Heat per tonne (5–20 bar, saturated, 60–105 °C feedwater) 650–750 kWh
Gas per tonne of steam 70–85 m³
Heavy fuel oil per tonne 60–75 kg
Coal (25 GJ/t) per tonne 105–125 kg
Wood chips (30% moisture) per tonne 230–280 kg
Electricity (electrode boiler) per tonne 660–760 kWh
Boiler efficiency, gas, with economiser 90–94% (net)

Tips to cut steam cost

  • Return more condensate. It saves fuel, water and treatment chemicals. Each 6 °C of feedwater temperature is worth about 1% of fuel.
  • Fit an economiser to recover stack heat into the feedwater; it typically adds 3–5 points of efficiency on gas boilers.
  • Control excess air with oxygen trim. Too much air carries heat up the stack.
  • Recover blowdown heat with a flash vessel and heat exchanger, and use automatic TDS control to avoid blowing down more than necessary.
  • Fix steam traps and insulation. A failed-open trap or bare valve wastes steam you have already paid for. Compressed air systems have similar hidden losses; see the compressed air leak calculator.
  • Lower the pressure where users allow. Losses from leaks and radiation fall, though the saving in boiler heat is small.

Limitations

This is the cost of steam leaving the boiler house. Distribution losses (often 5–15%), failed traps and condensate not returned raise the cost at the point of use. Boiler efficiency varies with load: a boiler cycling on and off at low load can be several points worse than its rating. Fuel energy content and price must be on the same basis (net calorific value here). For district or space heating comparisons, see the heating cost comparison.

Method & assumptions

Heat per tonne = (hsteam − hfeedwater) + blowdown × (hf,sat − hfeedwater), with saturated-steam enthalpies from IAPWS-IF97 tables at the boiler pressure. Fuel per tonne = heat ÷ boiler efficiency ÷ fuel energy content. Cost per tonne = fuel × price + water and treatment + CO₂ × carbon price.

Frequently asked questions

How much does it cost to produce one tonne of steam?
Mostly the fuel. A gas-fired boiler at 88% efficiency needs about 80 m³ of natural gas (765 kWh of fuel) per tonne of 10 bar steam from 90 °C feedwater. At 0.60 per m³ that is about 48 in fuel, plus 1–3 for water and treatment. Coal and biomass boilers usually make cheaper steam per tonne; electrode boilers are usually the most expensive.
How much energy is needed to make 1 tonne of steam?
About 2.4–2.7 GJ (670–750 kWh) of heat for saturated steam at 5–20 bar from feedwater at 60–105 °C. The total enthalpy of saturated steam is about 2,750–2,800 kJ/kg; subtract the feedwater enthalpy (4.19 kJ/kg per °C) to get the heat the boiler must add.
How much natural gas does a boiler use per tonne of steam?
Typically 70–85 m³ per tonne, depending on pressure, feedwater temperature and boiler efficiency. A 10 t/h boiler therefore burns roughly 700–850 m³ of gas per hour.
How does condensate return reduce steam cost?
Returned condensate is hot (often 80–95 °C) and already treated. Every 6 °C rise in feedwater temperature saves roughly 1% of fuel. Returning more condensate also cuts make-up water, chemicals and blowdown.
What is a good boiler efficiency?
Modern gas-fired shell boilers reach 85–89% on a net calorific basis without an economiser and 90–94% with one. Condensing economisers can go higher. Older oil and coal boilers often run at 75–82% because of high stack temperatures, excess air and radiation losses.
What is boiler blowdown and does it cost energy?
Blowdown removes water with concentrated dissolved solids to prevent scale and foaming. That water leaves at saturation temperature, so its heat is lost unless you fit a flash vessel and heat exchanger. Typical blowdown is 2–8% of steam flow.

Sources & references

  1. IAPWS — Revised Release on the IAPWS Industrial Formulation 1997 (IF97) for water and steam
  2. US DOE — Improving Steam System Performance: A Sourcebook for Industry
  3. US DOE — Steam Tip Sheets (feedwater, blowdown, condensate return, economisers)
  4. IPCC 2006 Guidelines, Vol. 2 Energy — fuel CO₂ emission factors

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.