Industry & business calculator

Compressed air leak calculator: what each leak costs per year

Flow through leaks of any size at your system pressure (choked-orifice formula), the compressor power and electricity they waste, the yearly cost and CO₂, the leak rate as a share of compressor capacity, and the payback of a repair campaign.

Editable share link Branded PDF report Free · no sign-up

Results

Leaks found: 31. At 7 bar they lose 63.4 l/s (134 cfm) of free air, keeping 24.7 kW of compressor power busy. That wastes 148,256 kWh and about 22,238 € a year. Repairs costing 1,240 € pay back in 0.7 months.
Annual cost of leaks
€22,238
148,256 kWh per year
Leak flow
63.4l/s
3.8 m³/min · 134 cfm
Compressor power wasted
24.7kW
Leak rate
25% of capacity
well-run systems: < 10%
CO₂ per year
67.9t
Repair cost
€1,240
31 leaks
Repair payback
0.7months
Cost of one 3 mm leak
€2,533
per year
Annual cost of one leak by hole size (€/yr)
Where the money goes

Leak flow and cost per hole at 7 bar(g)

Holel/scfmkWkWh/yr€/yr
0.5 mm0.20.40.0846970
1 mm0.81.70.311,877281
1.5 mm1.83.80.74,222633
2 mm3.216.81.257,5071,126
3 mm7.2215.32.8116,8902,533
4 mm12.8327.2530,0264,504
5 mm20.0542.57.8246,9167,037
6 mm28.8761.211.2667,56010,134
  • Choked (sonic) flow through a round orifice; free air at 1.013 bar and 20 °C. Hole size is an estimate: ultrasonic leak detectors with flow estimation give better numbers.
  • Leaks also force the compressor to run at higher pressure and longer, and can trigger the purchase of extra compressors; those costs are not included.

Why leaks are the cheapest saving in a factory

Compressed air is one of the most expensive forms of energy on a site. Only around 10–15% of the electricity a compressor uses ends up as useful work at the tool; the rest is heat. Leaks make it worse, because they run whenever the network is under pressure, including nights and weekends if the compressor stays on. They are also silent above the factory noise. In plants without a leak programme, they routinely take a fifth or more of compressor output.

This calculator turns the leaks found in a survey into flow, compressor power, kWh, money and CO₂. It also shows the leak rate as a share of compressor capacity and the payback of fixing them.

The formula

At typical network pressures the air leaving a hole reaches the speed of sound (choked flow), so the flow depends only on the hole and the upstream pressure:

ṁ = C_d × A × p₀ × √(γ ÷ (R·T)) × (2 ÷ (γ + 1))^((γ+1) ÷ (2(γ−1)))

A = π d² ÷ 4 p₀ = gauge pressure + 1.013 bar (absolute) γ = 1.4 R = 287 J/(kg·K) T = 293 K Free air flow Q = ṁ ÷ 1.204 kg/m³

Wasted power (kW) = Q (m³/min) × specific power (kW per m³/min) Annual cost = kW × pressurised hours × electricity price

With C_d = 1 this formula reproduces the Compressed Air Challenge reference value of 6.5 cfm for a 1/16” hole at 100 psig. Real leaks are irregular and lose less, so the default discharge coefficient is 0.65, close to DOE’s 0.61 for sharp-edged holes.

Worked example

The defaults describe a survey at 7 bar that found 20 small (1 mm), 8 medium (2 mm) and 3 clearly audible (3 mm) leaks, with a screw compressor using 6.5 kW per m³/min and a network pressurised 6,000 hours a year.

Hole Flow per leak Power per leak Cost per leak per year
1 mm 0.8 l/s (1.7 cfm) 0.31 kW ≈ 280
2 mm 3.2 l/s (6.8 cfm) 1.25 kW ≈ 1,130
3 mm 7.2 l/s (15.3 cfm) 2.81 kW ≈ 2,530
6 mm 28.9 l/s (61 cfm) 11.3 kW ≈ 10,100

Together the 31 leaks lose 63 l/s (3.8 m³/min, 134 cfm), which ties up 24.7 kW of compressor power. That is 148,000 kWh and about 22,200 a year at 0.15/kWh, plus 68 t of CO₂ at the world-average grid intensity. Against a 15 m³/min compressor this is a 25% leak rate, typical for an unmanaged system. At 40 per repair, the 1,240 campaign pays back in under a month.

Note how flow grows with the square of the hole diameter: one 3 mm leak wastes as much as nine 1 mm leaks.

How to read the results

  • Annual cost of leaks is the headline for management. It assumes the compressor makes up the lost air at its average specific power.
  • Leak rate compares the leak flow with compressor capacity. Above 10% there is a clear case for a programme; above 20–30% you may be running a compressor just to feed leaks.
  • Cost of one 3 mm leak is a useful figure for tagging campaigns: put a price on every tag.
  • The table shows flow and cost for each hole size at your pressure, ready to use with leak tags.

Tips beyond fixing leaks

  • Lower the pressure to what the most demanding user actually needs; each bar saved cuts about 7% of compressor energy and reduces leak flow.
  • Isolate idle areas with solenoid valves so that lines stop leaking when a shift ends.
  • Stop misusing air for cooling, blowing off or drying: an open blow-off tube is a deliberate 6 mm leak.
  • Control compressors well. Variable-speed or properly sequenced compressors avoid running unloaded. The motor energy savings calculator covers drive upgrades.

Limitations

Hole diameter is an estimate; ultrasonic detectors with flow estimation or a leak-down test give better figures. The specific power is an average: compressors running partly loaded or unloaded use more per m³, so the real cost of leaks can be higher. Effects on compressor maintenance, extra capacity bought because of leaks, and pressure drop at the point of use are not included.

Method & assumptions

Mass flow through a leak (choked flow): ṁ = Cd A p0 √(γ ÷ RT) × (2 ÷ (γ+1))(γ+1)/(2(γ−1)), with p0 the absolute pressure, γ = 1.4, R = 287 J/kg·K, T = 293 K. Free-air volume = ṁ ÷ 1.204 kg/m³. Power wasted = free air (m³/min) × compressor specific power (kW per m³/min). Annual cost = kW × pressurised hours × electricity price.

Frequently asked questions

How much does a compressed air leak cost?
At 7 bar, a 3 mm hole leaks about 7 litres of free air per second, which keeps about 2.8 kW of compressor power busy. Over 6,000 pressurised hours at 0.15 per kWh that costs around 2,500 a year. A 1 mm leak costs about 280 a year and a 6 mm leak more than 10,000.
What percentage of compressed air is lost to leaks?
The US DOE Compressed Air Challenge estimates that leaks waste 20–30% of compressor output in a typical plant that has no leak programme. Well-maintained systems keep leaks below about 10% of capacity.
How do I measure the leak rate of a compressed air system?
When no air is being used (for example at a weekend), run the compressor and time how long it runs loaded versus unloaded. Leakage (%) = loaded time ÷ (loaded + unloaded time) × 100. An ultrasonic leak detector locates individual leaks, and many models estimate the flow of each one.
How much electricity does a compressor use per m³ of air?
A modern rotary screw compressor at 7 bar uses about 6–7.5 kW per m³/min of free air delivered, equivalent to 0.10–0.125 kWh per m³ or 18–22 kW per 100 cfm. Older or part-loaded machines can use 30–50% more.
Does reducing pressure cut leak losses?
Yes. Leak flow is roughly proportional to absolute pressure, and compressor energy rises about 7% per bar (roughly 1% per 2 psi). Dropping the network from 8 to 7 bar cuts leak flow by about 11% and compressor energy per m³ by around 6–7%.
How quickly do leak repairs pay back?
Usually within weeks to a few months. Most leaks are in couplings, hoses, push-in fittings, filters, regulators and drains, which cost little to fix. The challenge is to keep finding them: leak programmes repeated every 3–6 months hold the savings.

Sources & references

  1. US DOE — Improving Compressed Air System Performance: A Sourcebook for Industry
  2. US DOE — Minimize Compressed Air Leaks (Compressed Air Tip Sheet #3)
  3. Compressed Air Challenge — Best Practices for Compressed Air Systems
  4. ISO 11011 — Compressed air: Energy efficiency assessment

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.