Energy finance calculator

Energy efficiency payback calculator: simple payback, ROI, NPV and IRR

Evaluate any energy-saving measure (lighting, motors, insulation, controls, heat recovery) from its cost, the kWh or fuel saved and the energy price: simple and discounted payback, ROI, NPV, IRR, savings-to-investment ratio and the cost of each kWh saved.

Editable share link Branded PDF report Free · no sign-up

Results

The measure pays back in 2.8 years (discounted: 3.1) and earns an IRR of 36.5%. Over 12 years it returns 51,730 € in today's money (NPV at 7%). Each kWh saved costs 0.052 €, against an energy price of 0.15 €.
Simple payback
2.8years
first-year saving 9,000 €
Discounted payback
3.1years
Net present value
€51,730
at 7% over 12 years
Internal rate of return
36.5%
Return on investment
369%
lifetime net savings ÷ net investment
Savings-to-investment ratio
3.07
> 1 means cost-effective
Cost of saved energy
0.052€/kWh
Lifetime energy saved
701MWh
Lifetime CO₂ avoided
280t
Cumulative cash flow (€)

Yearly savings

YearkWh savedPrice (€/kWh)Net saving (€)Cumulative (€)
160,0000.159,000-16,000
259,7000.1539,134-6,866
359,4020.1569,2702,404
459,1040.1599,40811,813
558,8090.1629,54921,361
658,5150.1669,69131,052
758,2220.1699,83540,887
857,9310.1729,98250,869
957,6420.17610,13060,999
1057,3530.17910,28171,281
1157,0670.18310,43581,715
1256,7810.18710,59092,305
  • Pre-tax, unlevered cash flows; tax depreciation and financing costs are not included. Savings should come from measured baselines (e.g. IPMVP) where possible.
  • Cost of saved energy = net investment × capital recovery factor + annual maintenance change, divided by annual kWh saved. Compare it with your marginal energy price.

How to judge an energy-saving measure

Most efficiency projects are judged on one number, simple payback, and many good ones are rejected because of it. A measure that pays back in four years but lasts twenty is often a better investment than one that pays back in two and lasts five. This calculator gives the payback figures managers ask for, plus the measures finance teams use: net present value (NPV), internal rate of return (IRR), savings-to-investment ratio (SIR) and the cost of each kWh saved.

It works for any measure whose benefit is lower energy use: lighting, motors and drives, insulation, controls, heat recovery, compressed-air repairs, boiler upgrades. Fuel savings can be entered in kWh with the fuel price per kWh.

The formula

Cash flow year 0 = −(investment − grants) Cash flow year t = kWh × (1 − decline)^(t−1) × price × (1 + escalation)^(t−1) − maintenance change

Simple payback = net investment ÷ first-year net saving NPV = Σ cash flow_t ÷ (1 + r)^t IRR = r at which NPV = 0 SIR = PV(savings) ÷ net investment Cost of saved energy = (net investment × CRF(r, life) + maintenance change) ÷ annual kWh CRF(r, n) = r(1 + r)^n ÷ ((1 + r)^n − 1)

Worked example

The defaults describe a 25,000 investment that saves 60,000 kWh a year at 0.15 per kWh, with 2% yearly price escalation, a 0.5% yearly decline in savings, a 12-year life and a 7% discount rate.

  • First-year saving: 60,000 × 0.15 = 9,000, so simple payback is 2.8 years. Discounting stretches it to 3.1 years.
  • Over 12 years the measure saves about 700 MWh. The NPV is about 51,700 and the IRR 36%.
  • SIR is 3.1: every unit invested returns about three in present-value savings.
  • Cost of saved energy: 25,000 × CRF(7%, 12) = 3,148 a year, divided by 60,000 kWh, gives 0.052 per kWh, about a third of the energy price.

The LED preset adds 1,500 a year of avoided lamp replacements and cuts the payback to 2.4 years. The insulation preset has a 5.9-year payback but a 30-year life, giving an IRR of 19% and an NPV comparable to the LED project. The building-controls preset shows the effect of savings that decline 3% a year.

Typical paybacks

Measure Typical simple payback Typical life
Compressed-air leak repair weeks to months 1–2 years (repeat)
LED lighting retrofit 1–4 years 10–15 years
Variable-speed drive on pump/fan 1–3 years 10–15 years
Building controls / BMS tuning 1–3 years 5–10 years
Premium-efficiency motor (at failure) 1–3 years (incremental cost) 15–20 years
Heat recovery 2–5 years 15–20 years
Roof or wall insulation 4–10 years 30+ years

How to read the results

  • Simple payback is easy to communicate but ignores everything after it.
  • NPV is the value the project creates in today’s money; any positive value beats leaving the cash at the discount rate.
  • IRR lets you compare the project with other uses of capital.
  • Cost of saved energy is the cleanest comparison with the energy price and with supply-side options. Compare it with the LCOE of new generation: efficiency is often the cheapest “power plant”.
  • The cumulative chart shows when the project breaks even, with and without discounting.

Limitations

Cash flows are pre-tax and unlevered; tax depreciation, interest and inflation are not modelled separately (treat the discount rate and escalation as real or nominal consistently). Savings estimates are often optimistic, so verify with metering. Rebound effects and interactions between measures (for example, LEDs reducing cooling load but increasing heating) are not included. For full project finance with debt and tax, use the NPV and IRR calculator.

Method & assumptions

Year-t cash flow = kWh saved × (1 − decline)t−1 × price × (1 + escalation)t−1 − maintenance change; year 0 = −(investment − grants). Simple payback = net investment ÷ first-year saving. Discounted payback, NPV and IRR use the discount rate on these cash flows. SIR = PV of savings ÷ net investment. Cost of saved energy = (net investment × CRF(rate, life) + maintenance change) ÷ annual kWh.

Frequently asked questions

How do I calculate the payback of an energy efficiency project?
Simple payback = net investment ÷ first-year savings. A 25,000 LED retrofit that saves 60,000 kWh at 0.15 per kWh plus 1,500 a year in maintenance saves 10,500 a year, so it pays back in about 2.4 years. Discounted payback, NPV and IRR give a fuller picture over the measure's life.
What is a good payback period for energy efficiency?
Many companies want 2–3 years for operational measures, which is a high hurdle: a 3-year payback on a 12-year measure corresponds to an IRR of roughly 30%. Long-lived measures such as insulation or heat recovery can be excellent investments with 5–8 year paybacks. NPV and IRR show this better than payback alone.
What is the cost of saved energy?
The annualised cost of a measure divided by the energy it saves each year: (investment × capital recovery factor + maintenance change) ÷ annual kWh. If it is lower than the price you pay for energy, the measure is cost-effective. Many lighting, controls and motor measures save energy at 0.02–0.06 per kWh.
What is the savings-to-investment ratio (SIR)?
SIR is the present value of lifetime savings divided by the net investment. A ratio above 1 means the measure pays for itself at the chosen discount rate; US federal energy programmes use SIR to rank projects.
Should I include energy price escalation?
Yes, but cautiously. A modest real escalation of 0–3% a year is common in business cases. Higher assumptions flatter long-lived measures, so test the result with 0% as well.
How do I know the savings are real?
Measure them. The International Performance Measurement and Verification Protocol (IPMVP) sets out how to establish a baseline, adjust for weather and production, and compare after the project. Use the savings-decline input to allow for controls that drift or equipment that ages.

Sources & references

  1. EVO — International Performance Measurement and Verification Protocol (IPMVP)
  2. US DOE FEMP — Life-cycle cost analysis (NIST Handbook 135)
  3. IEA — Energy Efficiency 2024
  4. Lawrence Berkeley National Laboratory — The cost of saving electricity through energy efficiency programs

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.