Coal is still the largest single source of electricity on Earth. In 2024 it generated about 34% of the world’s power, roughly 10,600 TWh, according to Ember’s Global Electricity Review 2025. Behind that number sits a surprisingly varied fuel, from hard, glossy anthracite to crumbly brown lignite that is half water, and a power plant design that has been refined for more than a century. This guide covers what coal actually is, how the different grades compare, and what happens between the coal yard and the transmission line. For who is closing plants and who is still building them, see Coal Phase-Out Around the World.
How coal forms, and why grades differ
Coal is plant matter that was buried in swamps, then compressed and heated over millions of years. Heat and pressure slowly drive out water, oxygen and volatile compounds and leave a richer share of carbon. Geologists call this progression rank. Low-rank coal is young and wet. High-rank coal is older, denser and more energy-rich.
| Rank | Typical carbon content | Moisture (as mined) | Energy content (MJ/kg, as received) | Main uses |
|---|---|---|---|---|
| Lignite (brown coal) | 25–35% | 30–60% | 8–15 | Mine-mouth power plants |
| Sub-bituminous | 35–45% | 15–30% | 18–24 | Power generation |
| Bituminous | 45–86% | 2–15% | 24–32 | Power, cement, coking coal |
| Anthracite | 86–97% | under 15% | 26–33 | Heating, specialist industrial uses |
Ranges follow the U.S. EIA and common industry classifications; individual seams vary a lot. Ash (the mineral matter that does not burn) and sulphur matter as much as rank. Indonesian sub-bituminous coal, the workhorse of Asian power stations, is prized partly because it is low in ash and sulphur even though its energy content is moderate, often 4,200–5,000 kcal/kg (about 17.5–21 MJ/kg). Australian export thermal coal is typically around 6,000 kcal/kg (about 25 MJ/kg). You can compare these against oil, gas and wood in the fuel energy content calculator.
Thermal coal versus metallurgical coal
Most coal is thermal coal, burned for heat. Buyers pay for energy, and contracts adjust the price for calorific value, ash and moisture. The main seaborne benchmarks are Newcastle (Australia, 6,000 kcal/kg) and Richards Bay (South Africa); Chinese and Indonesian indices cover lower grades. You can follow these on our coal prices page.
Metallurgical (coking) coal is a special group of bituminous coals. When heated without air in a coke oven, they soften, swell and fuse into coke, a hard porous carbon that both reduces iron ore and holds up the burden inside a blast furnace. Coking coal is a much smaller market, roughly a tenth of world coal output, but it is hard to replace. The blast furnace route makes about 70% of the world’s steel, and worldsteel puts its coal use at around 770 kg per tonne of steel produced.
World coal production hit a record of roughly 9 billion tonnes in 2024 according to the IEA’s Coal 2024 report, with China mining about half of it and India, Indonesia, the United States, Australia and Russia following.
Inside a pulverised coal power plant
Almost all large coal units today are pulverised coal (PC) plants. The process runs in a line:
- Coal handling. Coal arrives by train, conveyor or ship and is stockpiled. A 1,000 MW plant typically keeps several weeks of supply on site.
- Milling. Mills grind coal to a powder finer than flour, with most particles below 75 microns, so it burns almost instantly.
- Boiler. Hot air blows the powder into the furnace, where it burns at around 1,300–1,500 °C. Walls lined with thousands of metres of steel tubes absorb the heat and turn high-pressure water into steam.
- Turbine. Steam expands through high-, intermediate- and low-pressure turbine stages that spin at 3,000 rpm (50 Hz grids) or 3,600 rpm (60 Hz).
- Generator. The turbine shaft drives a generator producing electricity at around 20–25 kV, which a step-up transformer raises to transmission voltage.
- Condenser and cooling. Exhausted steam condenses back to water in a condenser cooled by river, sea or cooling-tower water, then pumps send it back to the boiler.
The flue gas leaving the boiler passes through pollution controls before it goes up the stack. A smaller number of plants use circulating fluidised bed (CFB) boilers instead, which burn crushed coal in a bed of hot sand and limestone at lower temperatures. CFBs tolerate poor-quality coal, biomass and waste fuels and capture sulphur inside the furnace.
Subcritical, supercritical, ultra-supercritical
The hotter and higher-pressure the steam, the more of the coal’s heat the turbine converts to work. Above 22.1 MPa (the critical point of water) water no longer boils in a distinct phase change, which allows “once-through” boilers with higher steam temperatures.
| Technology | Main steam pressure | Steam temperature | Net efficiency (LHV) | CO₂ per kWh (hard coal) |
|---|---|---|---|---|
| Subcritical | 16–18 MPa | ~540 °C | 33–37% | ~920–1,000 g |
| Supercritical | 23–25 MPa | 540–580 °C | 38–42% | ~800–880 g |
| Ultra-supercritical (USC) | 25–30 MPa | 580–620 °C | 42–47% | ~720–800 g |
| Advanced USC (R&D) | 30–35 MPa | 700 °C+ | ~48–50% target | ~670 g |
Values are typical ranges from IEA and manufacturer data. China has built the world’s largest USC fleet, and some of its best units report net efficiencies close to 46–48%. India’s fleet is younger than Europe’s but mostly subcritical, partly because Indian coal is high in ash (often 30–45%).
Heat rate: the number engineers watch
Plant operators usually talk about heat rate rather than efficiency: how much fuel energy it takes to make one kWh. It is just efficiency turned upside down. See the heat rate glossary entry for the unit conventions.
Example: a 1,000 MW supercritical unit at 40% efficiency Heat rate = 3,600 ÷ 0.40 = 9,000 kJ/kWh Coal use at full load (25 MJ/kg coal) = 1,000,000 kWh × 9,000 kJ/kWh ÷ 25,000 kJ/kg ≈ 360,000 kg/h ≈ 360 t/h ≈ 8,640 t/day CO₂ per kWh of electricity = 0.34 kg CO₂ per kWh of fuel (hard coal) ÷ 0.40 ≈ 0.85 kg CO₂/kWh
A one-percentage-point gain in efficiency on a large unit cuts its coal bill and CO₂ by roughly 2.5%. That is why plants spend heavily on turbine upgrades, cleaner boiler tubes and better condenser vacuum. Run your own numbers in the electricity CO₂ calculator.
Emission controls: what comes off the stack
Burning coal releases far more than CO₂. Modern plants stack several cleaning systems in series:
- Electrostatic precipitators (ESPs) or fabric filters charge and collect fly ash particles, removing more than 99% of dust by mass.
- Flue gas desulphurisation (FGD), usually wet limestone scrubbers, captures about 90–98% of sulphur dioxide and produces gypsum that can go into plasterboard.
- Selective catalytic reduction (SCR) injects ammonia over a catalyst to convert 80–90% of nitrogen oxides into nitrogen and water. Low-NOx burners help further upstream.
- Activated carbon injection captures mercury in some jurisdictions, including the US under its MATS rules.
These systems cost money and use a few percent of the plant’s own output, so many older plants in lower-income countries still run without full controls. None of them touch CO₂. Capturing that requires a separate post-combustion plant; see Carbon Capture and Storage Explained. Coal combustion also leaves large volumes of ash, which is either sold for cement and concrete or stored in ponds and landfills.
Where coal power runs today
China and India together produced about two-thirds of the world’s coal electricity in 2024. Coal supplied roughly 58% of China’s electricity and around 75% of India’s, according to Ember. Both countries are adding record amounts of solar and wind, but demand growth has kept coal output near its peak.
In Southeast Asia, coal grew fastest of any region over the past decade. Malaysia imports nearly all its coal, mainly from Indonesia, Australia and Russia, and burns it in a handful of large coastal plants:
| Plant (Peninsular Malaysia) | Approx. capacity | Notes |
|---|---|---|
| Manjung (Janamanjung), Perak | ~4,100 MW | Five units, including two newer ~1,000 MW supercritical/USC units |
| Jimah and Jimah East, Negeri Sembilan | ~3,400 MW | Jimah East has two 1,000 MW ultra-supercritical units |
| Tanjung Bin, Johor | ~3,100 MW | Includes a 1,000 MW supercritical unit |
| Kapar, Selangor | ~1,500 MW (coal units) | Older multi-fuel station |
Capacities are approximate and rounded from operator disclosures. Coal has made up around 40% or more of Malaysian generation in recent years (Ember), and the government’s National Energy Transition Roadmap commits to no new coal plants with a gradual retirement by about 2044. See the Malaysia country profile, how Malaysia’s electricity works and the Malaysia electricity hub.
Practical takeaways
- Coal is sold on energy, ash and sulphur, not tonnes alone. Lignite carries roughly a third of the energy per kilogram of good bituminous coal.
- Plant efficiency spans 33% to about 47%. Every point of efficiency removes about 2.5% of fuel use and CO₂.
- Modern controls deal with dust, SO₂ and NOx well; CO₂ needs separate capture equipment that few plants have.
- Coal still dominates power in China, India, Indonesia and much of Southeast Asia, while it is falling fast in Europe and North America.
For the data behind each country, explore the coal energy hub, the coal technology page and the global power plants map.
Calculators for this topic
Frequently asked questions
What is the difference between thermal coal and coking coal?
How efficient is a coal power plant?
How much CO₂ does coal power emit?
Why does lignite have such a low energy content?
Does Malaysia still use coal for electricity?
How much coal does a 1,000 MW plant burn?
Sources & references
Figures in this guide are typical ranges drawn from the sources above; your own numbers depend on location, prices and equipment. Use the linked calculators for site-specific estimates.