Electrical engineering calculator

Transformer sizing calculator: kVA rating, currents, losses and efficiency

Pick the standard transformer rating for a load with future growth, then see the loading, primary and secondary currents, no-load and load losses, efficiency curve, annual loss cost and the secondary short-circuit current.

Editable share link Branded PDF report Free · no sign-up

Results

A 630 kVA transformer covers 560 kVA including 20% growth. At peak it runs at 74% of rating and at average load at 37%. Losses are about 10,258 kWh a year (1,539 €), and secondary full-load current is 909 A.
Recommended rating
630kVA
required 560 kVA with margin
Loading at peak
74%
Secondary full-load current
909A
at 400 V
Primary full-load current
33.1A
at 11 kV
No-load loss
540W
iron loss, 24/7
Load loss at rated current
4,600W
copper loss ∝ load²
Efficiency at average load
99.45%
Peak efficiency
99.45%
at 34% load
Annual losses
10,258kWh
Annual cost of losses
€1,539
Secondary short-circuit current
22.7kA
uk 4%, infinite source
Efficiency and losses vs loading

Candidate ratings

Rating (kVA)Peak loadingNo-load loss (W)Load loss (W)Annual losses (kWh)Loss cost (€/yr)
50093%4593,90011,4611,719
63074%5404,60010,2581,539
80058%5856,0009,5961,439
1,00047%6937,6009,6951,454
1,25037%8559,50010,3901,558
  • Default losses are the EU Ecodesign Tier 2 maximum values for liquid-immersed transformers (Regulation 548/2014, amended 2019/1783); enter the datasheet values for your unit. Dry-type transformers have roughly 50–100% higher no-load losses.
  • Annual loss estimate treats the average load as constant. Because load losses go with the square of current, a peaky load profile loses somewhat more.

How this calculator sizes a transformer

A transformer is rated in kVA because its windings heat up according to current, whatever the power factor of the load. Sizing starts with the peak load in kW, divided by the power factor to give kVA. A margin is added for growth, and the result is rounded up to the next standard rating. The calculator then fills in what an engineer checks next: the loading at peak and on average, full-load currents on both sides, losses and efficiency, the yearly cost of those losses, and a first estimate of the secondary short-circuit current.

Default losses are the maximum values allowed for liquid-immersed distribution transformers under the EU Ecodesign Tier 2 rules, in force since July 2021. Any compliant transformer sold in Europe will be at or below them. Enter your datasheet values in the advanced fields for exact figures.

The formula

Required rating S_req = P ÷ PF × (1 + margin) → next standard size S_n

Full-load current I_n = S_n ÷ (√3 × V) Loading x = S_load ÷ S_n Losses P_loss = P0 + x² × Pk Efficiency η = x·S_n·PF ÷ (x·S_n·PF + P_loss) Maximum η at x = √(P0 ÷ Pk)

Secondary short-circuit current (infinite source) I_k ≈ I_n ÷ u_k

P0 is the no-load loss, Pk the load loss at rated current and u_k the impedance voltage (4% is usual up to 630 kVA and 6% above for 11–20 kV units).

Worked example

The defaults describe a building with a 420 kW peak at PF 0.9, a 20% margin and an average load of half the peak, supplied at 11 kV with a 400 V secondary.

  • Peak apparent power: 420 ÷ 0.9 = 467 kVA. With 20% margin: 560 kVA, so the next standard size is 630 kVA.
  • Loading: 74% at peak, 37% on average.
  • Full-load current: 630,000 ÷ (1.732 × 400) = 909 A on the secondary and 33 A on the primary.
  • Ecodesign Tier 2 losses for 630 kVA: P0 = 540 W, Pk = 4,600 W. At 37% loading the load loss is 0.37² × 4,600 = 631 W, so total losses are about 1.17 kW.
  • Annual losses: about 10,260 kWh, or roughly 1,540 a year at 0.15/kWh. Efficiency at average load is 99.45%, close to the maximum, which this unit reaches at 34% loading.
  • Secondary short-circuit current with an infinite upstream source: 909 ÷ 0.04 = 22.7 kA. Breakers on the main LV board need at least that breaking capacity. The short-circuit current calculator refines this with source impedance and cables.

Typical values (EU Tier 2, liquid-immersed)

Rating No-load loss P0 Load loss Pk 400 V full-load current
100 kVA 130 W 1,250 W 144 A
250 kVA 270 W 2,350 W 361 A
400 kVA 387 W 3,250 W 577 A
630 kVA 540 W 4,600 W 909 A
1,000 kVA 693 W 7,600 W 1,443 A
1,600 kVA 1,080 W 12,000 W 2,309 A
2,500 kVA 1,575 W 18,500 W 3,608 A

Older transformers, typical before 2015, often have no-load losses 50–100% higher. Since no-load loss runs 8,760 hours a year, that alone can justify replacing an old unit.

How to choose the margin

A 20–25% margin is common for commercial buildings and factories with expected growth. Add more if EV chargers, heat pumps or production lines are planned. Transformers can carry short overloads: IEEE C57.91 and IEC 60076-7 allow cyclic loading above nameplate when ambient temperature and the previous load were low. Sizing so that the normal peak sits at 70–85% of rating keeps hot-spot temperatures and ageing low.

For a solar or battery export connection, size the transformer for the inverter’s maximum kVA output, including reactive power capability, rather than for the average.

How to read the results

  • Recommended rating is the smallest standard size that covers the load with margin.
  • Loading at peak above 85% leaves little reserve; below 40% suggests the unit is oversized.
  • Annual cost of losses is the running cost of the transformer itself. Over 25–30 years it often exceeds the purchase price, which is why utilities evaluate tenders on capitalised losses.
  • Candidate ratings compare neighbouring sizes so you can weigh purchase cost against losses.

Limitations

The loss estimate uses a constant average load, while real profiles with high peaks lose somewhat more. Harmonic currents from drives and electronic loads raise load losses (see IEEE C57.110 for derating). Ambient temperature, altitude and enclosure ventilation affect the continuous rating. The short-circuit figure ignores upstream impedance and motor contribution, so it is a conservative first estimate.

Method & assumptions

Required rating S = P ÷ PF × (1 + margin), rounded up to the next IEC standard size. Full-load current I = S ÷ (√3 × V). Losses at loading x = Sload ÷ Sn: Ploss = P0 + x² × Pk. Efficiency η = x Sn PF ÷ (x Sn PF + Ploss); maximum efficiency occurs at x = √(P0 ÷ Pk). Secondary short-circuit current (infinite source) = In ÷ uk.

Frequently asked questions

How do I calculate the transformer size I need?
Divide the peak load in kW by the power factor to get kVA, add a margin for growth (typically 20–25%), and round up to the next standard rating. A 420 kW load at PF 0.9 is 467 kVA; with 20% margin that is 560 kVA, so a 630 kVA transformer.
What are the standard transformer kVA ratings?
The IEC preferred ratings for distribution transformers are 25, 50, 100, 160, 200, 250, 315, 400, 500, 630, 800, 1,000, 1,250, 1,600, 2,000, 2,500 and 3,150 kVA. North American practice uses 75, 112.5, 150, 225, 300, 500, 750, 1,000, 1,500, 2,000 and 2,500 kVA for three-phase units.
What is the full-load current of a 1,000 kVA transformer?
I = S ÷ (√3 × V). On a 400 V secondary that is 1,000,000 ÷ (1.732 × 400) = 1,443 A; at 415 V it is 1,391 A and at 480 V 1,203 A. On an 11 kV primary the current is only 52 A.
What are no-load and load losses in a transformer?
No-load (iron or core) loss is the power needed to magnetise the core. It is constant whenever the transformer is energised, even with no load. Load (copper) loss is the I²R heating of the windings and rises with the square of the load, so at half load it is a quarter of the rated value.
At what load is a transformer most efficient?
Efficiency peaks where load losses equal no-load losses, at a loading of √(P0 ÷ Pk). For modern low-loss distribution transformers that is typically 30–45% of rating, which suits buildings whose average load is well below the peak.
Is it bad to oversize a transformer?
A moderate oversize costs little in losses because modern units are efficient at partial load, and it leaves room for growth. A large oversize raises purchase cost and no-load losses, and also increases the prospective short-circuit current on the secondary, which can push up the breaker ratings needed.

Sources & references

  1. IEC 60076-1 — Power transformers, Part 1: General
  2. EU Commission Regulation 548/2014 (Ecodesign for power transformers), amended by 2019/1783
  3. US DOE — Energy conservation standards for distribution transformers (10 CFR 431)
  4. IEEE C57.91 — Guide for Loading Mineral-Oil-Immersed Transformers

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.