What this calculator does
A grid’s carbon intensity, or emission factor, is the CO₂ emitted per kWh of electricity. It depends almost entirely on the generation mix: how much comes from coal, gas and oil, and how much from nuclear, hydro, wind, solar and other low-carbon sources. Utilities, regulators and analysts build these factors constantly, for national inventories, corporate carbon accounting, EV and heat-pump comparisons, and scenarios for future grids.
Enter a generation mix and this tool calculates the factor on two bases: direct combustion (stack emissions, the convention for most inventories and Scope 2) and lifecycle (IPCC AR5 medians, which include the supply chain). It also converts the generation factor into a consumption factor by adding grid losses, and shows which sources drive the result.
The formula
Direct factor of a fossil plant = heat rate (GJ/kWh) × fuel CO₂ factor (g/GJ) coal ≈ 9.5 MJ/kWh × 94.6 g/MJ ≈ 900–950 g/kWh gas ≈ 7.2 MJ/kWh × 56.1 g/MJ ≈ 400 g/kWh
Consumption factor = generation factor ÷ (1 − T&D losses)
Default lifecycle values (g CO₂e/kWh, IPCC AR5 medians): coal 820, natural gas combined cycle 490, nuclear 12, hydro 24, onshore wind 11, utility solar 48, dedicated biomass 230, geothermal 38. Oil is not in the AR5 table; 720 g/kWh is an indicative literature value. Direct factors for coal, gas and oil can be edited under Fossil plant factors.
Worked example
The default mix is a generic grid in transition: 35% coal, 25% gas, 2% oil, 10% nuclear, 8% hydro, 10% wind, 7% solar, 2% bioenergy and 1% other.
- Coal: 0.35 × 950 = 332.5 g/kWh. Gas: 0.25 × 400 = 100. Oil: 0.02 × 740 = 14.8.
- Everything else is zero at the stack, so the direct factor is 447 g CO₂/kWh.
- With 6% grid losses the consumption factor is 447 ÷ 0.94 = 476 g/kWh.
- Coal supplies 35% of the electricity but 74% of the emissions.
- On a lifecycle basis the factor is about 436 g CO₂e/kWh. It is slightly lower because the AR5 coal median assumes a more efficient plant than the default fleet value.
Try the presets: a coal-heavy grid lands around 665 g/kWh, a gas-dominated grid around 340, a nuclear and hydro grid near 25, and a high-renewables grid around 110.
Typical grid factors
| Grid type | Example countries | Approximate intensity (g CO₂/kWh) |
|---|---|---|
| Hydro or nuclear dominated | Norway, Sweden, France, Switzerland | 20–60 |
| High renewables with some gas | Denmark, Portugal, Spain, United Kingdom | 100–200 |
| Mixed fossil and renewables | Germany, Italy, United States | 250–400 |
| Gas-dominated | Gulf states, Iran, Algeria | 400–550 |
| Coal-dominated | India, South Africa, Poland, Indonesia | 600–750 |
Values move every year as coal plants close and wind and solar grow. For the latest country figures from Ember and Our World in Data, use the electricity CO₂ calculator.
How to read the results
- Grid emission factor at generation is what most statistics report.
- Consumption factor is the one to use for kWh measured at a customer meter, if your reporting rules count losses.
- Direct vs lifecycle shows how much supply-chain emissions matter. They raise the figure for gas (methane leakage and processing) and give low-carbon sources small but non-zero values.
- The contribution chart shows which sources to replace first to cut emissions fastest. It is nearly always coal.
Limitations
An annual average hides hourly variation: a kWh at midday on a sunny day can have half the intensity of one in the evening peak. Imports and exports, combined heat and power allocation and the age of individual plants all change real factors. Marginal emission factors, which describe the effect of an extra kWh of demand, can be very different from the average. For corporate reporting follow the factor rules of the GHG Protocol; see the Scope 2 emissions calculator.
Method & assumptions
Grid factor = Σ sharei × factori, with shares normalised to 100%. Direct factors = plant heat rate × fuel CO₂ factor (coal ≈ 950, gas ≈ 400, oil ≈ 740 g/kWh by default); renewables and nuclear emit nothing at the stack. Lifecycle factors use IPCC AR5 median values. Consumption factor = generation factor ÷ (1 − T&D losses).
Frequently asked questions
How is a grid emission factor calculated?
What is the difference between direct and lifecycle emission factors?
What is a typical grid carbon intensity?
Why do grid losses increase the emission factor?
Why is the lifecycle factor for coal lower than the direct factor in this calculator?
Is bioenergy counted as zero emissions?
Sources & references
Embed this calculator
Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.