Power plants & fossil calculator

Gas turbine fuel consumption calculator: OCGT, CCGT and gas engines

How much natural gas a gas turbine, combined-cycle plant or gas engine burns per hour and per year in MMBtu, GJ, m³ and scf, including part-load and hot-weather penalties, plus fuel cost and CO₂ per MWh.

Editable share link Branded PDF report Free · no sign-up

Results

At 80% load and 25 °C the unit delivers 343.8 MW and burns 2,375 MMBtu of gas per hour (64,920 m³/h). Part-load efficiency is 54.7% LHV (heat rate 6,909 Btu/kWh HHV), so fuel costs 55.3 € per MWh.
Gas consumption
2,375MMBtu/h
2,506 GJ/h (HHV)
Volume flow
64,920m³/h
55.02 million scf per day
Mass flow
50.6t/h
Electrical output
343.8MW
available at 25 °C: 429.8 MW
Efficiency at this point (LHV)
54.7%
Heat rate (HHV)
6,909Btu/kWh
6,578 kJ/kWh LHV
Fuel cost per MWh
55.3€/MWh
CO₂ per MWh
367kg
Annual gas use
11.88million MMBtu
0.325 billion m³ · 11.46 Bcf
Annual generation
1,719GWh
Annual fuel + carbon cost
95million €
Annual CO₂
630kt
Gas flow and efficiency vs load
Output vs ambient temperature

Part-load table

LoadOutput (MW)Efficiency (LHV)Heat rate (Btu/kWh HHV)MMBtu/hm³/h€/MWh
30%128.944%8,5851,10730,25468.7
40%171.947.8%7,9151,36137,18763.3
50%214.950.3%7,5121,61444,12160.1
60%257.952.2%7,2441,86851,05458
70%300.853.6%7,0522,12257,98756.4
80%343.854.7%6,9092,37564,92055.3
90%386.855.6%6,7972,62971,85454.4
100%429.856.4%6,7072,88278,78753.7
  • Part-load and ambient corrections are generic curves for screening. Manufacturer correction curves (output, heat rate vs load, temperature, humidity, altitude) give exact values.
  • CO₂ factor 53.06 kg/MMBtu HHV (US EPA). Gas density assumed 0.78 kg/m³; m³ at 15 °C, 1 atm.

How this calculator works

Gas turbines are rated at ISO conditions: 15 °C, sea level, 60% relative humidity and full load. Real plants rarely run there. A peaker in a desert summer may lose 15% of its output, and a combined-cycle plant following load overnight might sit at 50–60% load for hours. Both increase gas use per MWh.

This tool starts from the datasheet efficiency and rated output, then applies two generic corrections. The first is a hot-weather derate for ambient temperatures above 15 °C. The second is a part-load penalty that raises the heat rate as load falls. From the corrected heat rate it computes gas flow in MMBtu/h, GJ/h, m³/h, scf and tonnes per hour, along with yearly totals, fuel cost per MWh and CO₂.

The formula

Heat rate at ISO full load: HR = 3,600 ÷ η_LHV (kJ/kWh)

Available output: P_avail = P_ISO × (1 − d × (T_amb − 15)) Ambient heat rate: HR_T = HR × (1 + 0.25 × d × (T_amb − 15)) Part load: HR(L) = HR_T × (1 + k × (1/L − 1))

Gas flow (GJ/h, LHV) = HR(L) × P_avail × L ÷ 1,000 HHV = LHV × 1.108 1 MMBtu = 1.055 GJ m³ = GJ_HHV × 1,000 ÷ HHV (MJ/m³)

Default part-load coefficients k: 0.28 for heavy-duty open cycle, 0.22 for aeroderivatives, 0.12 for F-class combined cycle, 0.10 for H/J class, 0.06 for gas engines. Default hot-weather derates d: 0.6–0.7%/°C for simple-cycle turbines and about 0.45%/°C for combined cycles. Gas engines barely notice ambient temperature, so their derate is set very low.

Worked example

The defaults model a 450 MW F-class combined-cycle plant at 57% LHV, running at 80% load on a 25 °C day for 5,000 hours a year, with gas at 8 per MMBtu.

  • At 25 °C the available output is 450 × (1 − 0.0045 × 10) = 429.8 MW; at 80% load the plant delivers 343.8 MW.
  • The ISO heat rate of 6,316 kJ/kWh rises 1.1% for temperature and another 3% for part load, to 6,578 kJ/kWh LHV. That is 54.7% efficiency, or 6,909 Btu/kWh on an HHV basis.
  • Gas flow is 6,578 × 343.8 ÷ 1,000 = 2,262 GJ/h (LHV), or 2,506 GJ/h (HHV) = 2,375 MMBtu/h, about 64,900 m³ per hour.
  • Fuel cost is 2,375 × 8 ÷ 343.8 = 55.3 per MWh; CO₂ is 2,375 × 53.06 kg ÷ 343.8 = 367 kg/MWh.
  • Over 5,000 hours: 1,719 GWh, 11.9 million MMBtu (0.33 billion m³) and 630 kt of CO₂.

Switch to the “Peaker 100 MW, 600 h” preset to see the other end: a hot 35 °C day knocks 12% off output, and gas use per MWh is about 50% higher than in the combined cycle.

Typical values

Plant type Full-load efficiency (LHV) Heat rate (Btu/kWh, HHV) Gas per MWh
H/J-class combined cycle 60–63% 6,000–6,300 6.0–6.3 MMBtu, ≈ 165 m³
F-class combined cycle 55–58% 6,500–6,900 6.5–6.9 MMBtu, ≈ 180 m³
Aeroderivative open cycle 38–42% 9,000–9,900 9–10 MMBtu, ≈ 255 m³
Heavy-duty open cycle 34–38% 9,900–11,100 10–11 MMBtu, ≈ 285 m³
Gas engine (≥ 5 MW) 44–49% 7,700–8,600 7.7–8.6 MMBtu, ≈ 220 m³
Microturbine 25–30% 12,600–15,100 12.6–15 MMBtu

The US fleet average for gas combined cycles is close to 7,500 Btu/kWh and for gas turbines around 11,000 Btu/kWh, according to EIA. Starts, part load and older units explain the gap with new-plant figures.

How to read the results

  • Gas consumption (MMBtu/h) is the number to give a gas supplier or pipeline operator. The m³/h and million scf per day figures cover metric and US gas contracts.
  • Efficiency at this point shows how far you are from the datasheet. If it falls more than 10% below full-load efficiency, consider running fewer units at higher load.
  • Fuel cost per MWh is the plant’s marginal fuel cost. Compare it with the power price to judge the “spark spread”.
  • The part-load table shows why combined cycles prefer to stay above 50–60% load, while gas engines can follow demand with little penalty.

Limitations

The part-load and temperature corrections are generic curves for screening studies. Real machines have stepped behaviour (inlet guide vanes, sequential combustion, units dropping out of a multi-shaft block), and humidity, altitude and inlet or exhaust pressure losses also matter. Start-up fuel is not included: a hot start of a large CCGT can burn several hundred MMBtu before it reaches minimum load. Use the manufacturer’s correction curves for contracts. For other fuels or steam plants, use the heat rate calculator, and to compare gas prices in different units, the energy price converter.

Method & assumptions

Heat rate at ISO full load = 3,600 ÷ efficiency (kJ/kWh, LHV). Above 15 °C available output falls by the hot-weather coefficient per °C and heat rate rises by a quarter of that loss. Part load: HR(L) = HRfull × (1 + k × (1/L − 1)), with k ≈ 0.25–0.3 for simple-cycle turbines, 0.1–0.12 for combined cycles and 0.05 for gas engines. Fuel (GJ/h, LHV) = HR × MW ÷ 1,000; HHV = LHV × 1.108; 1 MMBtu = 1.055 GJ; m³ = GJ (HHV) ÷ heating value.

Frequently asked questions

How much gas does a gas turbine use per hour?
Fuel flow equals output times heat rate. A 100 MW open-cycle turbine at 37% efficiency (about 10,300 Btu/kWh HHV) burns roughly 1,030 MMBtu per hour at full load, which is about 28,000 m³ of pipeline gas. A 450 MW F-class combined-cycle plant at full load needs around 3,000 MMBtu/h.
How much natural gas is needed to generate 1 MWh?
About 6.5–7.5 MMBtu (HHV) in a combined-cycle plant and 9.5–11.5 MMBtu in an open-cycle peaker. In volume, that is roughly 170–200 m³ per MWh for a CCGT and 250–300 m³ per MWh for a simple-cycle turbine.
What is the difference between OCGT and CCGT fuel consumption?
A combined-cycle plant recovers the hot exhaust of the gas turbine in a heat-recovery steam generator and drives a steam turbine with it. That adds about 50% more output for the same gas, raising efficiency from 35–42% (open cycle) to 55–63%. Per MWh, a CCGT uses roughly 35–40% less gas.
Why does a gas turbine use more fuel in hot weather?
Hot air is less dense, so the compressor pushes less mass through the turbine. Output falls by roughly 0.5–0.8% per °C above the 15 °C ISO rating for heavy-duty and aeroderivative units, and the heat rate rises too. Inlet cooling (evaporative or chillers) recovers part of the loss.
How efficient is a gas turbine at part load?
Efficiency drops noticeably below full load. A simple-cycle turbine at 50% load typically has a heat rate 25–35% higher than at full load; a combined cycle loses less, around 8–15%, because the steam cycle and multi-shaft arrangements help. Reciprocating gas engines hold their efficiency best.
How do I convert MMBtu to cubic metres of gas?
1 MMBtu is 1.055 GJ. Divide by the gas's gross heating value: at 38.6 MJ/m³ (typical pipeline gas), 1 MMBtu ≈ 27.3 m³, or about 1,000 standard cubic feet.

Sources & references

  1. US EPA — GHG Emission Factors Hub (natural gas 53.06 kg CO₂/MMBtu)
  2. US EIA — Average operating heat rate by prime mover and energy source
  3. ISO 3977-2 — Gas turbines: standard reference conditions and ratings
  4. US DOE / NETL — Cost and Performance Baseline for Fossil Energy Plants, Vol. 1 (natural gas combined cycle)

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.