Home energy guide

Air Conditioning Energy Use: Costs, Ratings and Savings

How much electricity air conditioners use, what EER, SEER and CSPF mean, inverter vs non-inverter, Malaysian star ratings and a worked TNB cost example.

Updated 6 min read 1,312 words

In a Malaysian home, the air conditioner is usually the biggest item on the electricity bill, often more than the fridge, water heater and everything else combined. The same is true across Southeast Asia, the Gulf, India and the southern United States. Cooling is one of the fastest-growing uses of electricity in the world, and it peaks on hot afternoons and evenings when grids are under the most strain. This guide explains how much energy air conditioners really use, how to read the efficiency labels, and what cuts the bill most.

Cooling in global numbers

The IEA’s report The Future of Cooling (2018) put the number of air conditioners in use at about 1.6 billion in 2016, using around 2,000 TWh a year, roughly 10% of global electricity. In its baseline scenario the stock would rise to about 5.6 billion units by 2050, which works out to around ten new units sold every second for the next 30 years. China, India and Indonesia account for much of the growth.

Ownership tracks income and heat. More than 90% of households in the US and Japan have air conditioning, against roughly 10% in India in the late 2010s. In Malaysia, ownership has grown fast: most urban households in the Klang Valley now run at least one split unit.

Cooling demand rises with temperature and humidity, measured in cooling degree days. Kuala Lumpur has well over 3,000 cooling degree days a year (base 18 °C), several times more than southern Europe, and the demand barely varies by season.

How an air conditioner works

An air conditioner is a heat pump running in cooling mode. A compressor pressurises refrigerant gas, which gives off heat in the outdoor coil (condenser) and turns liquid. The liquid passes through an expansion valve, becomes cold and evaporates in the indoor coil, absorbing heat and moisture from the room. In humid climates a large part of the work goes into removing water from the air, which is why indoor units drip.

Capacity is still sold in “horsepower” in Malaysia and much of Asia, which is a loose trade term rather than motor power:

Trade size Cooling capacity Typical room size
1.0 hp ~9,000 BTU/h (~2.6 kW) up to ~15 m²
1.5 hp ~12,000 BTU/h (~3.5 kW) ~15–22 m²
2.0 hp ~18,000 BTU/h (~5.3 kW) ~22–30 m²
2.5 hp ~24,000 BTU/h (~7.0 kW) ~30–40 m²

Room sizes are rough guides for normal ceiling height; west-facing rooms, top floors and large windows need more.

Efficiency ratings: EER, SEER, CSPF

Rating What it measures
EER Cooling output ÷ electrical input at one fixed test condition (full load)
SEER Seasonal efficiency over a range of outdoor temperatures and part loads (US, EU versions differ)
CSPF Cooling Seasonal Performance Factor, ISO 16358, used in Malaysia, Thailand, Indonesia, Singapore and Japan

Seasonal ratings matter more than EER because an air conditioner spends most of its time at part load. Malaysia’s Energy Commission (Suruhanjaya Tenaga) sets Minimum Energy Performance Standards (MEPS) for air conditioners under the Electricity Regulations, and its 1- to 5-star energy label is based on CSPF. Good 5-star inverter units in Malaysia reach CSPF values above 5, meaning they move more than 5 kWh of heat out of the room per kWh of electricity. Old fixed-speed units can be closer to 3.

Inverter vs non-inverter

A fixed-speed (“non-inverter”) unit runs its compressor at full power until the room reaches the setpoint, then switches off, then on again. An inverter unit changes compressor speed to match the heat load, running gently most of the time. Benefits:

  • Typically 20–40% less electricity when used for several hours a day;
  • Steadier temperature and better dehumidification;
  • Lower start-up current, which matters for generators and solar systems.

Inverter units cost more, often RM300–800 more for a 1.5 hp unit in Malaysia, but with nightly use the savings usually repay that within a few years.

Worked example: a 1.5 hp unit in Malaysia

Assume a 1.5 hp inverter unit cooling a bedroom 8 hours a night, with an average draw of 0.8 kW after the first cool-down. For the tariff we assume an all-in rate of about 45 sen/kWh, roughly what TNB’s domestic tariff from July 2025 adds up to for households using under 1,500 kWh a month before service tax, Automatic Fuel Adjustment and the energy efficiency rebate. Check the current figures on the TNB tariff page.

Daily energy = 0.8 kW × 8 h = 6.4 kWh Monthly energy = 6.4 × 30 ≈ 192 kWh Monthly cost = 192 kWh × RM0.45 ≈ RM86

Same room, old non-inverter unit drawing 1.15 kW on average: 1.15 × 8 × 30 = 276 kWh × RM0.45 ≈ RM124 (≈ RM38 a month more)

Raising the setpoint from 22 °C to 25 °C (assume −20%): 192 × 0.8 ≈ 154 kWh ≈ RM69 a month

Run your own numbers in the air conditioner cost calculator or the appliance energy cost calculator, and see how the total fits your bill with the electricity bill calculator.

What saves the most

Ranked roughly by impact for a typical tropical home:

  1. Setpoint. Every degree higher saves roughly 5–10%. Malaysia’s Energy Commission and Singapore’s NEA suggest 24–25 °C. A ceiling fan running alongside makes 26 °C feel like 23–24 °C for a few watts.
  2. Right size, inverter, high star rating. An oversized unit short-cycles and dehumidifies poorly; an undersized one runs flat out.
  3. Shade and insulation. Most heat gain in tropical homes comes through the roof and west-facing windows. Roof insulation, reflective roofing, external shading and window film cut the cooling load directly.
  4. Close the room. Gaps under doors and open windows let humid air in, and removing moisture costs as much energy as cooling.
  5. Maintenance. Dirty filters and coils can raise consumption by 10–15%. Clean filters every few weeks and service the unit once or twice a year.
  6. Timer and sleep mode. Many people cool an empty bedroom for hours before bed.

Rooftop solar lines up well with daytime cooling. See Solar ATAP and Malaysian solar and size a system with the solar panel calculator.

Refrigerants and the climate

Refrigerants leak during installation, servicing and disposal, and many are powerful greenhouse gases.

Refrigerant GWP (100-year, approx.) Status
R-22 (HCFC) ~1,800 Ozone-depleting; being phased out under the Montreal Protocol
R-410A (HFC blend) ~2,090 Common in older and some current units
R-32 (HFC) ~675 Now standard in most new split units in Asia
R-290 (propane) ~3 Used in some new units; flammable, needs careful installation

The Kigali Amendment to the Montreal Protocol, agreed in 2016 and in force since 2019, commits countries to cut HFC use by 80–85% by the late 2040s. Malaysia ratified it in 2020. Correct installation and proper recovery of refrigerant at disposal matter as much as the choice of gas.

Cooling and the grid

Air conditioning is the main reason peak electricity demand in hot countries occurs on weekday afternoons and evenings. Peninsular Malaysia’s demand peaks have repeatedly hit records during heatwaves. Efficient units, building standards and smart thermostats that can shift cooling by an hour all reduce the generation and network capacity needed. Read more in demand response explained and how Malaysia’s electricity system works. For cities, central plants can do the job more efficiently; see district heating and cooling.

Practical checklist

  • A 1.5 hp inverter unit used 8 hours a night uses roughly 150–250 kWh a month.
  • Buy inverter and look at the CSPF and star rating, not just the price.
  • Set 24–26 °C and add a fan; each degree saves about 5–10%.
  • Shade the roof and west windows before buying a bigger unit.
  • Prefer R-32 or R-290 units and use a licensed installer.

Calculators for this topic

Frequently asked questions

How much electricity does a 1.5 hp air conditioner use?
A 1.5 hp split unit has a cooling capacity of about 12,000 BTU/h, or 3.5 kW. A modern inverter model typically draws 0.5 to 1.2 kW once the room is cool, so 8 hours of night-time use often comes to 5 to 8 kWh. Older non-inverter units can use 30 to 50% more.
Does setting the AC to 25 °C instead of 22 °C save money?
Yes. Each degree you raise the setpoint cuts cooling energy by roughly 5 to 10%, depending on climate and the unit, so moving from 22 to 25 °C can save around 15 to 25%. Malaysia's Energy Commission and Singapore's National Environment Agency both recommend about 24 to 25 °C.
What does CSPF mean on a Malaysian AC label?
CSPF is the Cooling Seasonal Performance Factor: total cooling delivered over a typical year divided by electricity used, measured to ISO 16358 with a Malaysian temperature profile. A higher CSPF means lower bills. The Energy Commission's star rating, from 1 to 5 stars, is based on it.
Is an inverter air conditioner worth it?
In most homes, yes. An inverter varies compressor speed to match the load instead of switching on and off, which typically saves 20 to 40% of electricity compared with a fixed-speed unit used for several hours a day. The higher price usually pays back within two to four years in a hot climate with daily use.
Which refrigerant is best for the environment?
Lower global warming potential is better if the refrigerant leaks. R-32 has a GWP of about 675, roughly a third of R-410A at about 2,090. Propane (R-290), with a GWP of about 3, is used in some newer units. Old R-22 also damages the ozone layer and is being phased out under the Montreal Protocol.
How much of the world's electricity goes to cooling?
The IEA estimated in The Future of Cooling (2018) that space cooling used about 2,000 TWh, roughly 10% of global electricity. It is one of the fastest-growing uses, driven by rising incomes and heat in Asia, the Middle East and Africa.

Sources & references

  1. IEA (2018). The Future of Cooling
  2. Suruhanjaya Tenaga (Energy Commission Malaysia): Energy efficiency labelling and MEPS
  3. Tenaga Nasional Berhad: Domestic tariff
  4. UNEP Ozone Secretariat: Kigali Amendment to the Montreal Protocol
  5. IPCC AR6 WG1, Chapter 7: Global warming potentials of refrigerants

Figures in this guide are typical ranges drawn from the sources above; your own numbers depend on location, prices and equipment. Use the linked calculators for site-specific estimates.