Home energy calculator

Pool pump running cost and variable-speed savings

Works out how many hours a day your pool pump needs to run, what it costs per month and per season, and how much a variable-speed pump saves by running slower for longer. Based on pool volume, turnover rate and the pump affinity laws.

Editable share link Branded PDF report Free · no sign-up

Results

Your single-speed pump needs 5.4 hours a day and costs 301 € a season. A variable-speed pump at 50% runs 10.7 hours but uses 65% less energy, saving 195 € a season and paying back in 6.2 years.
Single-speed cost per season
€301
1,075 kWh
Hours per day (single-speed)
5.4h
75 m³ filtered per day
Variable-speed cost per season
€106
380 kWh
Hours per day (variable-speed)
10.7h
at 194 W
Saving per season
€195
65% less energy
Variable-speed payback
6.2 years
Cost per month (single-speed)
€50.16
CO₂ saved per season
208kg
Seasonal cost vs pump speed (same water filtered)
Hours per day needed vs speed
  • Halving the pump speed halves the flow but cuts the power to roughly one sixth (affinity laws, with real-world motor losses). The pump must run twice as long, so the energy for the same filtration falls by about two thirds (75% with the pure cube law).
  • Too low a speed may not run a salt chlorinator, solar heater or pool cleaner properly; many owners run a short high-speed period each day and the rest at low speed.

How this pool pump calculator works

A pool pump has one job: push the pool’s water through the filter often enough to keep it clean. That gives a fixed amount of water to move each day, and the question is how much electricity it takes to move it. The calculator starts from your pool volume and target turnovers per day, divides by the pump’s flow rate to get the hours it must run, and multiplies by its power and the length of your swimming season.

It then repeats the sum for a variable-speed pump running at a lower speed. Slower means longer hours, but the power falls so steeply with speed that the energy for the same filtration drops sharply. The difference is your seasonal saving, and the pump price divided by that saving is the payback.

The formula

Water to filter per day = pool volume × turnovers Hours per day = water to filter ÷ flow rate

Variable-speed flow = full flow × speed Variable-speed power = full power × speed^2.5

Season energy = power × hours per day × (months × 30.4) Cost = energy × electricity price Payback = variable-speed pump cost ÷ seasonal saving

The pump affinity laws say flow is proportional to speed and power to the cube of speed. In real pool plumbing, motor and drive losses at low speed make the electrical power fall a little less steeply, so the calculator uses an exponent of 2.5 rather than 3. This keeps the estimate on the cautious side.

Worked example

The defaults describe a 50 m³ pool (a typical in-ground pool of about 10 × 4.5 m, 1.1 m average depth) with 1.5 turnovers a day, used six months a year. The single-speed pump draws 1.1 kW and moves 14 m³/h through the filter and pipes. Electricity costs €0.28/kWh.

  • Water to filter: 50 × 1.5 = 75 m³ a day.
  • Single-speed: 75 ÷ 14 = 5.4 hours a day. Over 182 days that is about 1,075 kWh, or €301 a season (around €50 a month).
  • Variable-speed at 50%: flow 7 m³/h, so 10.7 hours a day, at 1.1 × 0.5^2.5 ≈ 194 W. Season energy about 380 kWh, or €106.

The variable-speed pump saves about €195 a season, 65% of the energy, and pays back its €1,200 installed cost in about 6.2 years. On a 300 g/kWh grid it also avoids around 208 kg of CO₂ a year. With a longer season, as in Florida, Queensland or the Mediterranean, the saving roughly doubles and the payback halves.

How to read the results

  • Single-speed cost per season is the headline: what you pay now.
  • Hours per day for each pump show how long they must run. If the variable-speed figure goes above 24 hours, the chosen speed is too low for your turnover target.
  • Saving per season and payback are the numbers to compare with quotes from pool shops.
  • The cost vs speed chart shows how fast the cost falls as you slow the pump. The steepest gains come between 100% and 50%; below about 30% the extra hours and motor losses eat into the benefit.

Typical values

Item Typical range
Residential pool volume 30–100 m³ (8,000–26,000 US gal)
Turnovers per day 1–2 (hot climate or heavy use 2–3)
Single-speed pump input 0.75–1.9 kW (1–2 hp motors)
Real flow with filter and pipes 8–20 m³/h
Variable-speed low setting 30–60% of full speed
Energy saving with variable speed 50–80%

Tips to cut pool pump costs

  • Measure the real flow. The rating on the box is open-flow; a dirty filter and long pipe runs can cut it by a third. A flow meter or the filter pressure gauge tells you what is really happening.
  • Lower the turnover target. If the water stays clear at one turnover, you do not need two.
  • Clean the filter and skimmer baskets. A clogged filter makes any pump work harder.
  • Use a pool cover. It reduces debris, evaporation and heat loss, so the pump and heater work less.
  • Run it on cheap power. With a time-of-use tariff or rooftop solar, shift the hours, not just the speed. The solar panel calculator shows how much daytime power a roof could provide.

Limitations

The model assumes the pump curve and your plumbing stay the same at every speed and that the same filtration is needed. It does not include pool heating, which is usually a much larger cost than the pump if you heat the water, nor chlorinators or robotic cleaners. Some salt systems and solar heaters need a minimum flow, so the lowest speed may not be usable. Season length is entered in months of 30.4 days. For the electricity cost of other equipment around the house, use the appliance energy cost calculator or the home energy audit.

Method & assumptions

Water to filter per day = pool volume × turnovers. Hours = volume to filter ÷ flow. Variable-speed flow = full flow × speed; power = full power × speed2.5 (the theoretical cube law, corrected for motor and drive losses at low speed). Season energy = power × hours × days in use (months × 30.4). Payback = pump cost ÷ yearly saving.

Frequently asked questions

How much does it cost to run a pool pump?
A typical 1 to 1.5 hp single-speed pump draws about 1.1 to 1.6 kW. Running 5 to 8 hours a day over a six-month season, that is roughly 1,000 to 1,700 kWh, or about €280 to €480 at €0.28/kWh. A variable-speed pump doing the same filtration usually costs a third of that.
How many hours a day should a pool pump run?
Long enough to pass the whole pool volume through the filter one to two times a day. Divide the volume to filter (pool volume × turnovers) by the pump's real flow rate. With 50 m³, 1.5 turnovers and 14 m³/h, that is about 5.4 hours on a single-speed pump.
Do variable-speed pool pumps really save money?
Yes, because pump power falls much faster than flow. At half speed the flow halves but the electrical power drops to roughly a sixth, so the pump runs twice as long and still uses about 65% less energy. Payback is commonly 2 to 7 years depending on season length and electricity price.
What speed should I run a variable-speed pump at?
As low as still gives proper skimming, filtration and enough flow for heaters, salt chlorinators and cleaners. Many owners run 40 to 60% speed most of the day and a short high-speed period for the cleaner or after heavy use.
Is it cheaper to run the pool pump at night?
Only if you have a time-of-use tariff with cheaper night rates, or you can run it in the middle of the day on your own solar power. The energy used is the same; what changes is the price per kWh.
What is a pool turnover?
One turnover means a volume of water equal to the whole pool has passed through the filter. Residential pools usually aim for one to two turnovers a day, more in hot weather or with heavy bather loads.

Sources & references

  1. ENERGY STAR: Pool Pumps
  2. US DOE Energy Saver: Swimming Pool Covers and efficient pool operation

Embed this calculator

Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.