How this space heater calculator works
Space heaters are simple machines, which makes their running cost easy to work out once you know three things: how much power the heater draws, how much of the time it actually runs, and what you pay per kWh. This calculator takes the heater’s input power and your price to get the cost per hour on full, applies a duty cycle for the time the thermostat keeps it switched on, and multiplies up to a day, a month and a whole winter.
It also does two checks people often skip. The first compares the heater’s output with the heat a room of your size and insulation needs in cold weather, so you can see if it will cope or run flat out all day. The second puts every heater type side by side for the same amount of heat, which shows why the type of electric heater matters much less than the advertising suggests, and why a heat pump is in a different league.
The formula
Heat output = input × COP (COP = 1 for resistance and flame heaters) Room heat need = floor area × 45 / 70 / 100 W/m²
Worked example
The defaults describe a 1.5 kW oil-filled radiator switched on 6 hours a day for 120 days of winter, with the thermostat keeping it running 60% of the time. Electricity costs €0.28/kWh. The room is 16 m² with average insulation.
- On full power: 1.5 × €0.28 = €0.42 an hour.
- With the thermostat cycling: €0.42 × 0.6 = €0.25 an hour, so €1.51 a day.
- Over the winter: €1.51 × 120 = €181, for 648 kWh of electricity (about €46 a month).
- Every kWh of heat costs €0.28, because all the electricity becomes heat.
- The room needs about 16 × 70 W = 1.1 kW in cold weather, so the 1.5 kW heater has some margin.
In the comparison chart, every resistance heater lands on the same €181. A split air conditioner heating with a COP of 3.2 would deliver the same heat for about €57. An LPG cabinet heater would cost around €132 and a kerosene heater €135 at the default fuel prices.
How to read the results
- Cost per winter is the headline, based on your hours and duty cycle.
- Cost per hour at full power is the worst case, for example while warming a cold room.
- Heat output vs room need: if the output is below the need, the heater will run continuously in cold weather and the room may still not reach temperature. Raise the duty cycle to 100% to see that cost.
- Cost per kWh of heat compares directly with other heating. The heating cost comparison does the same for boilers and heat pumps.
Typical values
| Heater | Typical power | Heat per kWh of input |
|---|---|---|
| Oil-filled radiator | 1–2.5 kW | 1 kWh |
| Fan heater | 2–3 kW | 1 kWh |
| Convector / panel heater | 1–2.5 kW | 1 kWh |
| Infrared / halogen | 0.4–2 kW | 1 kWh (heats people, not air) |
| Split heat pump (heating) | 0.5–1.5 kW input | 2.5–4 kWh |
| LPG cabinet heater | 1.5–4.2 kW | 1 kWh of gas |
| Kerosene heater | 2–3 kW | 1 kWh of fuel |
Tips to cut space heater costs
- Heat the room you are in, not the house. Used this way, a small heater can save money compared with heating every room.
- Use the thermostat and a timer. A heater left on full in an empty room is the most common waste.
- Close the door and block draughts. The heater only needs to cover the room’s losses.
- Consider infrared for spot heating. In a draughty workshop or at a desk, warming you directly with a few hundred watts beats heating all the air.
- Look at a heat pump. If you heat one room most of the winter, a split unit costs about a third as much to run. The heat pump calculator shows the numbers for a whole house, and the air conditioner cost calculator covers sizing.
Limitations
The duty cycle is a single average; real cycling depends on outdoor temperature, insulation and the thermostat setting. The room heat need uses simple W/m² rules for about −5 °C outside and a 2.5 m ceiling, so treat it as a sanity check, not a heat-loss calculation. Heat pump COP falls in very cold weather. Fuel prices for LPG and kerosene vary widely, and bottled kerosene in particular costs much more than bulk heating oil.
Method & assumptions
Cost per hour at full power = input kW × price per kWh (LPG price ÷ 12.8 kWh/kg, kerosene price ÷ 9.6 kWh/L). Real cost per hour = full-power cost × duty cycle. Day = hourly cost × hours; winter = day × days. Heat output = input × COP (1 for resistance and flame heaters). Room need = area × W/m² for the insulation level.
Frequently asked questions
How much does it cost to run a space heater per hour?
Which type of electric heater is cheapest to run?
Is an oil-filled radiator cheaper than a fan heater?
What size heater do I need for my room?
Is it cheaper to use a space heater than central heating?
Are LPG and kerosene heaters safe indoors?
Sources & references
Embed this calculator
Free for blogs, installers, schools and NGOs. Copy the code below; it updates itself automatically.